S&S Cycle GBL Series Carburetor Master Rebuild Kit 11-2912 Harley-Davidson

S&S Cycle GBL Series Carburetor Master Rebuild Kit 11-2912 Harley-Davidson
S&S Cycle GBL Series Carburetor Master Rebuild Kit 11-2912 Harley-Davidson

S&S Cycle GBL Series Carburetor Master Rebuild Kit 11-2912 Harley-Davidson

S&S GBL 1 3/4 Series Carburetor Master Rebuild Kit. Fits GBL carbs for Harley-Davidson motorcycles.

Includes a body rebuild kit, all new fasteners, springs, and idle mixture screw. (includes #3,4,13,14,23,29,31,32,52,53,54,55,56,57,58). Installation Instructions: Throttle Shaft Bushing. All S&S® Carburetors Except E & G Series Super and Two-Throat. Two methods of repair are given to restore. Wear determines which method to use.

Bodies with extreme wear will generally have. This makes it impossible to. Enlarge the hole as described in the Minimal. Wear Method and expect to have the hole. Located in the correct position.

Advisable to use the Extreme Wear Method. If there is any doubt. Method cannot be used, return the carb body. Carb bodies with minimal wear.

NOTE: Repair work for carbs with minimal wear. Can be done using a drill press. Using machinists vise or 90 angle plate. Clamp carb body so that both throttle shalt.

Holes can be drilled from same side of body. On Super carbs make bowl gasket surface.

All early style and L Series. S&S carbs must have bowl gasket surfaces. Lined up 90 to drill plane perpendicular to.

For all carburetors use N letter drill. Drill must be long enough so. That when it is inserted in drill chuck both.

Throttle shaft holes can be drilled in one. Operation from same side of carb body. Line up throttle shaft hole by centering on. Carefully drill out throttle shaft holes. Without removing carb from clamps ream. Drilled throttle shaft holes with 516.

Enough to ream both throttle shaft holes in. One operation from same side of carb body.

Start bushing with this end. NOTE: When correctly installed, bushing will not.

Be flush with the out side of throttle shaft boss. Bushing is not pressed in far enough, air will leak. Past throttle plate causing erratic carburetor. Ream throttle shaft bushings with. Bushings in one operation from the same. Bores are correctly aligned and that throttle. Shaft has correct clearance when installed. NOTE: For all drilling and reaming operations.

The use of coolant or lubricant on tool is. Recommended to insure a clean cut and a.

If reaming operation is not performed. Throttle shaft may bind and stick due to. If throttle inadvertently sticks in open. Position, loss of control of motorcycle and. Personal injury to you or others may result.

Thoroughly clean carb and reassemble with new parts, making sure to install. Throttle plate with beveled surface sealed.

Carb bodies with extreme wear. NOTE: Repair work for carbs with extreme.

Wear must be done using a milling machine. Use machinists vise or 90 angle plate. To hold carb body and bolt to mill table.

Super carb bowl gasket surfaces must. Be lined up 90 to table while all early. S&S® carb bowl gasket surfaces must. Position and clamp assembly so that. Throttle shaft hole is directly below chuck.

All early style and L Series carbs have. Throttle shaft hole locations as illustrated. 3125 endmill cutter with flutes. Longer than depth of hole to be cut.

Feed cutter when making new hole. Long lead on one end. With this end and press to within. NOTE: When correctly installed, bushing will. Not be flush with the out side of throttle shaft. If bushing is not pressed in far enough. Air will leak past throttle plate causing erratic.

Repeat steps 1 through 4 for opposite. Ream both throttle shaft bushings with. Shaft bushings from the same side of carb. This insures that bushing bores are.

Correctly aligned and that throttle shaft. Has correct clearance when installed in. Position, loss of control of motorcycle. And personal injury to you or others may. Thoroughly clean carb and reassemble.

With new parts, making sure to install. Harley-Davidson & V-Twin Chopper Motorcycles. Stock is subject to change. Visit Our Other e B a y Stores. Purchasing means you accept all knowledge of condition, size and fitment. The item "S&S Cycle GBL Series Carburetor Master Rebuild Kit 11-2912 Harley-Davidson" is in sale since Tuesday, February 18, 2020. This item is in the category "eBay Motors\Parts & Accessories\Motorcycle Parts\Air Intake & Fuel Delivery\Carburetors & Parts".

The seller is "vital-v-twin-cycles" and is located in West Liberty, Iowa. This item can be shipped worldwide.


S&S Cycle GBL Series Carburetor Master Rebuild Kit 11-2912 Harley-Davidson